Logo Printing on Bags: Methods, Costs and What Lasts

Logo printing on bags is where most bulk orders go right or wrong. The fabric can be perfect and the stitching can be tight, but if the logo cracks after three washes or the brand blue comes out looking purple, that's the part the client remembers. We get the blame for it too, which is fair, because the print method is a choice the factory should help the buyer make.

The trouble is that most buyers are told about one method only: whatever the supplier's own machine does. A unit with a screen printing table will tell you screen print is best. A shop with a DTF printer will say DTF is the future. Both can be right, for different bags and different quantities.

At our bag factory in Mumbai we run screen printing, heat transfer, DTF, sublimation and embroidery under one roof, and we send offset and foil work to partner presses we have used for years. So this guide covers all of them with the rupee costs we actually quote, the minimums that make each one worth doing, and the mistakes we see in artwork files every single week.

The six ways a logo goes onto a bag

Every branded bag you have ever received was decorated in one of six ways. Some bags combine two, such as an embroidered logo on the front and a screen printed sponsor list on the back. The table below is the quick version; each method gets its own section further down.

MethodHow it worksBest forWeak point
Screen printingInk pushed through a mesh stencil, one screen per colour1 to 4 colour logos, 300 pieces and upPhotos and gradients
Heat transfer vinyl (HTV)Cut vinyl pressed on with heatNames, numbers, very small runsEdges can lift on soft fabric
DTF (direct to film)Full-colour print on film, glued and pressed onto the bagMulti-colour art, 50 to 500 piecesFeels slightly rubbery, costs more per piece
SublimationDye turned to gas and set into polyester fibreAll-over prints on white or light polyesterDoes not work on cotton, jute or dark fabric
EmbroideryLogo stitched in thread by a multi-head machinePremium laptop bags, canvas totes, small logosPuckers thin fabric, costly for big logos
Offset and foil (paper and laminated bags)Printed on sheets or film before the bag is madePaper bags, laminated non-woven, 1,000 pieces and upHigh setup, not possible on finished bags

If you only take one thing from this table: the method follows the fabric and the quantity, not the other way round. Pick the bag first, then the print.

Screen printing: still the workhorse

Most of the bags that leave our floor are screen printed. It is cheap at volume, the ink sits well on non-woven bags, cotton, canvas and jute, and a good print outlasts the bag. Our screen printed bags page shows the typical finish.

The process is simple to explain. We expose your artwork onto a mesh screen, one screen per colour. A printer lays each bag flat on the table, pulls ink across the screen with a squeegee, and the bag goes onto a drying rack or through a flash dryer. Two colours means two screens and two passes, lined up by hand or on a registration jig.

Water-based or plastisol ink

We use water-based ink on light cotton and jute because it soaks into the fibre and feels soft. Plastisol sits on top of the fabric, gives brighter colour on dark bags and is the usual choice for non-woven and polyester. If your bag is black or navy and the logo is white, plastisol with an under-base gives the cleanest result. Water-based white on black cotton tends to look grey unless it is printed twice.

What screen printing costs

Screen printing has a fixed cost (the screen and setup) and a running cost per piece. That is why it gets cheaper as the order grows. These are the bands we quoted through 2026 for a print area up to about 10 x 12 inches.

ItemRough costNotes
Screen and setupRs 600 to Rs 1,200 per colour per sideOne-time; reused if you reorder the same art
Print, 1 colour, 1 sideRs 4 to Rs 8 a pieceAt 500 to 1,000 pieces
Each extra colourAdds Rs 3 to Rs 8 a piecePlus a new screen
Second sideRoughly the same as the first sideNeeds its own screens
Oversize print (above 12 x 14 in)Adds 30 to 50 percentBigger screen, more ink, slower drying

Worked example: 1,000 cotton totes, two-colour logo on one side. Two screens at about Rs 900 each is Rs 1,800, which is under Rs 2 a bag when spread over the run. Printing adds about Rs 10 to Rs 14 a bag. On 100 bags, the same screens add Rs 18 a bag, and that is when DTF starts to win.

Heat transfer and DTF for short runs and full colour

These two get mixed up all the time, partly because both use a heat press. They are different products.

Heat transfer vinyl is a coloured sheet that a plotter cuts into your logo shape. We weed away the waste and press what is left onto the bag. It works for one or two solid colours and is the easiest way to put a different name on every bag, which is why sports academies and schools ask for it on drawstring bags and kit bags.

DTF (direct to film) is newer. A special printer puts your full-colour artwork, including photos and gradients, onto a PET film with a white backing layer. Powder adhesive is added and cured, and then the film is pressed onto the bag. Because there are no screens, a 60-colour illustration costs the same as a one-colour logo. That one fact has changed small orders more than anything else in the last five years.

Point of comparisonHeat transfer vinylDTF transfer
Colours possible1 to 2 solid coloursUnlimited, photos included
Setup costAlmost noneNone
Cost per print (A5 size)Rs 12 to Rs 30Rs 18 to Rs 35
Cost per print (A4 size)Rs 25 to Rs 45Rs 35 to Rs 50
Sensible order size1 to 200 pieces50 to 500 pieces
Feel on the bagSmooth, slightly plasticSlightly raised, rubbery
Fabric it suitsPolyester, canvas, cottonCotton, canvas, polyester, rPET, blends
Does not suitJute, non-woven below 80 GSMJute (rough weave), thin non-woven

A word of caution on DTF. A cheap transfer pressed at the wrong temperature will peel at the corners within a month. We press at a set temperature and time for each fabric and do a peel test on the first ten bags of every batch. Ask any supplier what their press settings are. If they can't tell you, expect problems.

Sublimation for all-over prints

Sublimation is the only method where the print becomes part of the fabric instead of sitting on it. Special ink is printed on paper, and under heat and pressure it turns into a gas and dyes the polyester fibres. You can run your hand over it and feel nothing.

It has two hard limits. The fabric must be polyester or a high-polyester blend, so it will not work on cotton, canvas or jute. And the bag must be white or a very light colour, since sublimation ink is see-through and cannot cover a dark base. Within those limits, it gives the best full-colour result of any method, including edge-to-edge patterns. We use it most on rPET bags and white polyester drawstrings for marathons and school events.

Expect Rs 25 to Rs 60 a bag depending on how much of the bag is covered. For all-over designs we often print the fabric panels before stitching, which costs less than pressing finished bags and avoids the white creases you get at the seams.

Embroidery when the bag needs to feel expensive

An embroidered logo on a laptop bag or a heavy canvas tote reads as premium in a way a print never quite does. HR teams pick it for joining kits, and it is the default for leadership gifts. You can see examples on our embroidered bags page.

Embroidery is priced by stitch count, not by colour. A neat 3-inch logo is usually 5,000 to 8,000 stitches. A 6-inch logo with fill areas can cross 25,000, and the price climbs with it. Before stitching, the logo has to be digitised, which means converting the artwork into a stitch file; this is a one-time charge.

Logo sizeTypical stitch countCost per pieceGood on
2 to 3 inch, text or simple mark3,000 to 6,000Rs 20 to Rs 30Laptop sleeves, pouches, caps
3 to 4 inch, logo with small fill6,000 to 10,000Rs 30 to Rs 45Backpacks, messenger bags, canvas totes
5 to 6 inch, full fill15,000 to 25,000Rs 50 to Rs 70Duffle bags, premium totes
Digitising (one time)Not applicableRs 500 to Rs 1,500Reused on reorders

Where we push back: embroidery on 210D polyester or cotton below 160 GSM. The fabric is too thin to hold the stitches, so it puckers around the logo. On those bags, a woven label stitched on, or a small embroidered patch, gives the same feel without spoiling the bag.

Paper bags and laminated bags are printed before they are made

With paper bags and laminated non-woven, the print goes onto flat sheets or film first, and the bag is formed after. That allows offset printing, with photo-quality colour, gold foil and spot UV. It also means you cannot add a logo to stock bags later; the run has to be planned from the start. We covered paper bag finishes in detail in our custom printed paper bags guide.

Laminated non-woven and laminated jute bags use a printed BOPP film bonded to the fabric. The print quality is like a magazine cover, but plates and cylinder costs mean it only works out at around 3,000 to 5,000 pieces and above. Below that, a two-colour screen print on plain laminated fabric is the smarter spend.

Which print method suits which bag

This is the table we wish every buyer saw before sending artwork. It matches fabric to the methods we would actually recommend, and to the one we would steer you away from.

Bag fabricFirst choiceAlso worksAvoid
Non-woven 70 to 120 GSMScreen print (plastisol)Offset on laminated non-wovenDTF and embroidery
Cotton 140 to 180 GSMScreen print (water-based)DTFLarge embroidery
Canvas 8 to 12 ozScreen printEmbroidery, DTFSublimation
Jute and jucoScreen print (thick ink)Patch or labelDTF, fine-line art
Polyester 210D to 600DScreen print or DTFEmbroidery on 600D, sublimation on whiteEmbroidery on 210D
rPETScreen printSublimation on whiteHeavy embroidery
PaperOffset or flexoScreen print on short runs, foilAnything after forming

Jute deserves a special mention. The weave is open, so fine text under about 4 mm fills in and becomes unreadable. If you want small lettering on jute bags, we print it on a cotton pocket or patch and stitch that on. Our jute bag price guide has the patch costs.

Choosing by quantity and budget

Quantity changes the answer more than most buyers expect. The same logo on the same cotton bag can be cheapest by DTF at 100 pieces and cheapest by screen print at 1,000. Here is roughly how a two-colour, one-side logo on a cotton tote works out per bag, print cost only.

Order sizeScreen print (incl. screens)DTFEmbroidery (3 in logo)Our usual advice
50 piecesRs 45 to Rs 60Rs 20 to Rs 35Rs 55 to Rs 75DTF
100 piecesRs 28 to Rs 36Rs 20 to Rs 35Rs 45 to Rs 60DTF, or screen if 1 colour
300 piecesRs 15 to Rs 22Rs 20 to Rs 32Rs 35 to Rs 45Screen print
1,000 piecesRs 10 to Rs 14Rs 18 to Rs 30Rs 30 to Rs 40Screen print
5,000 piecesRs 7 to Rs 10Rs 18 to Rs 28Rs 28 to Rs 38Screen print

These numbers move with print size and ink colour, and there is a floor; our minimum order quantity page explains the smallest runs we take per bag type. For full bag-plus-print figures, the bulk pricing page and our custom tote bag cost breakdown are a better starting point.

Getting the artwork right the first time

Half the delays we see come from artwork, not production. A buyer sends a 200-pixel logo pulled from their website, we ask for a vector, and three days pass while the design agency is chased. Send the right file on day one and you save that week.

Here is the checklist we send to new clients:

  • Send vector files (AI, EPS, PDF or SVG). For DTF and sublimation, a 300 DPI PNG at actual print size also works.
  • Convert all text to outlines so the font does not change on our system.
  • Give Pantone references for brand colours, not just "our blue".
  • Tell us the print size in inches and its position (centre, top, near the handle).
  • Keep lines thicker than 0.5 mm for screen print and 1 mm for jute.
  • Mention if the logo has a gradient. That decides between screen and DTF.

On colour matching: screen ink can be mixed close to a Pantone, usually within a shade a buyer would not notice. DTF and sublimation print from CMYK, so very bright oranges, neon greens and some royal blues come out slightly duller. If your brand lives or dies on one colour, ask for a strike-off (a test print on the real fabric) before bulk production. On larger orders we usually include one in the sampling stage.

How we check print quality before dispatch

A logo that looks fine on the drying rack can fail in a customer's kitchen. Our quality control team runs the same checks on every printed batch:

CheckHow we do itWhat fails it
Rub testDry and wet white cloth rubbed over the printInk transferring onto the cloth
Tape testStrong tape pressed on the print and pulled offFlakes of ink or film lifting
Stretch testPrinted area pulled by handCracks in the ink layer
Wash test (cotton, canvas)Sample bag hand washed and driedFading or peeling after one wash
Position checkTemplate laid over random bagsLogo off centre by more than about 5 mm

Under-cured plastisol is the most common fault we find in bags made elsewhere and sent to us for reprinting. It looks fine but rubs off when wet. The fix is simple (proper drying temperature and time) but it slows a line down, which is why rushed suppliers skip it. You can read about the rest of our manufacturing process if you want the full sequence.

Lead times by print method

Printing usually overlaps with stitching, so it rarely adds the full time below to the order. Still, the method affects your dispatch date, especially for large or rushed jobs.

MethodSample or strike-offBulk (1,000 pieces)Bulk (5,000 pieces)
Screen print2 to 3 days3 to 5 days7 to 10 days
Heat transfer vinyl1 day4 to 6 daysNot advised
DTF1 to 2 days4 to 6 days10 to 14 days
Sublimation2 days4 to 6 days8 to 12 days
Embroidery3 to 4 days (incl. digitising)6 to 8 days12 to 18 days
Offset and foil (paper)5 to 7 days10 to 15 days total15 to 20 days total

For a conference bag order, give yourself three weeks from artwork approval to delivery. Two weeks is possible for screen printed non-woven or cotton; it is tight for anything embroidered. During October and November, when Diwali gifting fills every line in the city, add a week to all of it.

Who orders what

After this many years in the trade, we can usually guess the print method from the first line of the enquiry. These are the patterns we see most often.

BuyerTypical bagUsual printWhy
Corporate HR teamsLaptop backpack, canvas toteEmbroidery or small screen printLooks premium, logo stays subtle
Pharma brandsConference bag, doctor kit bag2-colour screen printBrand and product name, large runs
Retail storesNon-woven or paper carry bagsScreen or offsetCost per bag matters most
Event organisersCotton or non-woven toteScreen, with sponsor logos on the backMany logos, fixed date
Schools and academiesDrawstring, backpacksScreen plus vinyl namesSame crest, different student names
D2C and Etsy sellersCotton or canvas totesDTFSmall runs, detailed art

For pharma launches, our bags for pharmaceutical companies page lists the formats doctors actually keep. Shop owners should look at bags for retail stores and our non-woven wholesale price list.

How to order printed bags from us

The steps are the same for 200 bags or 20,000:

  • Send us the bag type, quantity, size, logo file and delivery date on WhatsApp or through the contact form.
  • We reply with a quote that lists the bag, print method, screen or digitising charges and freight separately.
  • You approve a digital mock-up showing logo size and position.
  • For orders above 500 pieces, we make a physical sample or strike-off. Approve it, or ask for changes.
  • Bulk production starts after the advance payment. We send photos from the floor during the run.
  • We dispatch by tempo within Mumbai and by courier or road transport elsewhere in India, with a packing list per carton.

Buyers outside Mumbai order the same way. We regularly ship to Bengaluru, Delhi and Hyderabad; our Bangalore page covers delivery times there. If you already have bags and only need printing, we do take print-only jobs, but only on fabrics we know, since we can't stand behind a print on a bag we didn't make.

Frequently asked questions

What is the cheapest way to print a logo on bags?

For 300 pieces or more, a one-colour screen print on one side is the cheapest, often Rs 4 to Rs 8 a bag plus a one-time screen charge. Below 100 pieces, DTF usually works out cheaper because there are no screens to pay for.

How long does screen printing last on a cotton bag?

A properly cured screen print lasts the life of the bag, which is usually 30 or more washes for cotton. Fading after a few washes means the ink was under-cured or the wrong type for the fabric.

Can you print a photo on a jute bag?

Not well. The weave of jute breaks up fine detail. We print the photo by DTF on a cotton patch and stitch the patch onto the jute bag, which looks far better.

Is DTF the same as screen printing?

No. Screen printing puts ink straight onto the fabric through a stencil and needs one screen per colour. DTF prints the full design on film and transfers it with heat, so it handles any number of colours with no setup.

What is the minimum order for logo printed bags?

It depends on the bag. For stock non-woven and cotton bags with screen print we usually start at 300 to 500 pieces. With DTF on stock totes, smaller runs are possible. Our logo printed bags page lists the current options.

Do you charge for the screen again if I reorder?

Usually not, if the artwork and print size are unchanged and the reorder is placed while we still have the screen. Embroidery files are kept, so digitising is not charged again. Confirm this when you place the reorder.

If you have a logo and a rough quantity in mind, send them to us on WhatsApp at +91 86525 70502 or through our quote form. We'll tell you which print method suits your bag, what it costs at your quantity, and whether a cheaper option would do the job just as well.

← Back to Blog Request a Quote